Energy Saver

Posts Tagged ‘AXIAL’

IN THIS VIDEO WE GO THROUGH THE HUB SPINDAL AND BEARINGS. THEN WE CLEAN EVERYTHING UP, AND INSPECT THE PARTS. AFTER THAT WE REPLACE THE BEARINGS AND TAP OUT THE RACES AND REPLACE THEM, PACK THE BEARING WITH GREASE, TAP IN NEW RACES, AND INSTALL THE NEW SEAL, BEARINGS, AND COMPLETELY ASSEMBLE THE FINISHED ASSEMBLY. I DID A LOT OF EDITING TO FIT IN ALL THE INFORMATION, AND VIDEO THAT I COULD. THIS IS IN ORDER TO KEEP THE WHOLE PROCESS IN ONE 15 MINUTE VIDEO. ALSO I SHOW A SMALL CLIP OF THE FINISHED MAGNET ROTR AFTER CASTING. IT CAME OUT NICE! THE FOOTAGE CAME FROM THE NEXT VIDEO, (PART 19). I HOPE YOU REALY ENJOY THESE 2 VIDEOS, AND SHARE THEM. THIS VIDEO IS FREE SO ALL CAN ENJOY THE FULL BUILD OF A WIND TURBINE BUILT FROM SCRATCH, INSTEAD OF SPENDING 200 BUCKS TO LEARN HOW TO BUILD FROM SOME FLY BY NIGHT SCAM ARTISTS VERSION OF FREE ENERGY. I URGE YOU TO DOWN LOAD THE WHOLE SERIES AS IT IS PRESENTED. U2B VIDEOS DONT LAST FOREVER. YOU NEVER KNOW. WHY TAKE A CHANCE. I DONT PLAN ON LEAVING ANYWAY. NOT FOR A LONG TIME I HOPE. GOD BLESS ALL OF YOU, AND ALL OF YOUR LOVED ONES. KEEP SMILING AND HAVE A BALL. MUDDy

PART 17 DUAL PERMANENT MAGNET ROTOR AXIAL FLUX WIND TURBINE DESCRIPTION: IN THIS VIDEO, WE MAKE THE MAGNET ROTOR TEMPLATE FOR PLACING MAGNETS ON THE ROTOR. THEN WE TAP THE HUB AND DRILL THE JACKING BOLT HOLES AND TAP THEM. AND SHOW THE HUB , SPINDAL, AND BEARING SET UP. AND DISCUSS A FEW THINGS ABOUT KEEPING BALLANCE THROUGHOUT THE UNIT. AND WE SHOW HOW TO TAP THE HOLES THE RIGHT WAY, ALSO WE DISCUSS THE REASON FOR USIN A 27/64ths INCH DRILL BIT SO THE INNER DIAMETER OF THE THREADS IS NOT LOST. IF WE USED A 1/2 INCH DRILL BIT, THERE WOULD BE NO THREADS TO MAKE. THANKS! MUDDy

WELL WE FINALLY CAST THE STATOR. THE WIFE AND I HAD A BALL. I HOPE YOU ALL HAVE AS MUCH FUN AS WE DID. THE CASTING WENT LIKE A DREAM, EXCEPT FOR ALL THE BUGS THAT SHOWED UP FOR THE 500 WATT LIGHT. IN THIS VIDEO WE CAST THE STATOR, AND SHOW TIPS FOR MAKING IT COME OUT RIGHT. GREASING THE MOLD, MIXING THE POLYESTER RESIN, WHY WE USE BABY POWDER IN THE MIX, PAINTING THE MOLD WITH RESIN, THE FIBERGLASS SHEET, RESIN, THEN COILS, MORE RESIN, THE NEXT FIBERGLASS SHEET, AND THE REST OF THE RESIN. THEN WE SEAL UP THE MOLD AND SCREW IN ALL THE SCREWS. MUDDy

IN THIS EDITION WE FINISH ALL PARTS OF THE MOLD, AND WAX IT HEAVILY. THEN WE PREPARE THE MOLD, AND CUT THE FIBERGLASS MESH FABRIC TO FIT THE MOLD. NOW THE MOLD IS SEALED , WAXED, AND THE FABRIC IS CUT. THE WAX HAS BEEN HEATED TO FILL IN THE GAPS AND MAKE A SMOOTH SURFACE FOR RELEASE. CASTING IS NEXT. THANKS FOR THE PATIENCE IN WAITING FOR ALL THE WORK TO BE DONE. ALL OF THIS PREPARATION IS A MUST. JUST LIKE PAINTING A CAR. YOU CANT JUST START SPRAYING THE CAR THANKS FOR WATCHING. MUDDy

THE MOMENT WE’VE ALL BEEN WAITING FOR. OPENING THE STATOR MOLD. WHEN THE CATAPILLAR MAKE THE BUTTERFLY EMERGE. A LITTLE EXPLANATION OF TROUBLES AND CURES FOR THOSE PROBLEMS. AND THE FINAL STATOR GETS TESTED BY OHMS METER. .5 OHMS ON EACH COIL. AND THEN A FEW ADDED TID BITS FOR THE NEXT VIDEOS. THANKS. MUDDy

IN THIS VIDEO, WE WORKED OUT THE REST OF THE PROBLEMS WITH THE GREEN MACHINE AXIAL FLUX WIND TURBINE ALTERNATOR. AND PARTIALLY ASSEMBLE THE UNIT. I GROUND OUT SOME METAL JOINTS, AND DISSASEMBLED THE PARTS, AND REWELDED THEM IN THEIR TRUE ALLIGNMENTS. PLUS I SHOWED HOW I GOT THE TRUE ALLIGNMENTS BEFORE WELDING. AND A FEW TRICKS FOR MAKING ALL THIS MATCH UP THE RIGHT WAY. THE NEXT VIDEO, PART 3, SHOULD SHOW THE FULL ASSEMBLY OF THIS UNIT. THANKS FOR WATCHING. MUDDy

HEY GUYS, THANKS FOR WATCHING. AND THANKS FOR WAITING SO LONG AS I HAD TO WORK A FEW LONG HOURS SINCE THE LAST PART. IN THIS VIDEO, WE DO ABOUT HALF OF THE METAL WORK INVOLVED IN MAKING THIS 750 WATT MACHINE. JUST A FEW PARTS CUT AND WELDED. THEN WE DRILL HOLES FOR THE STATOR ALL-THREADS, AND SLAP IT TOGETHER IN PART 22 OR PART 23. I ALREADY HAVE THE 3 PHASE BRIDGE RECTIFIERS, AND I HAVE HAD ONE OF THEM APART ON CAMERA TO SHOW HOW SIMPLE THEY ARE TO REBUILD IN THE EVENT OF A BLOWOUT. SIMPLE LITTLE CRITTERS… WELL ITS OFF TO BOOM BOOMS’ BOOM TOWN LABs TO FINISH UP ON THIS METAL WORKS, AND A FEW OTHER PROJECTS TO PLAY WITH. MAN! BOOMER HAS A LOT OF NICE TOYS. I WILL USE HIS WELDER TO FINISH UP. HOPEFULLY WE CAN BUILD A REALLY DECENT CRYSTAL RADIO TO PLAY WITH. HOPEFULLY PART 22 WILL BE UP AND RUNNING ON THE CHANNEL TOMORROW NIGHT. THE WEATHER FORECAST HAS A LOT TO DO WITH WHAT WE GET TO DO FOR FUN THERE. RAIN IS EXPECTED ALL WEEKEND. THE DUAL ESCAPEMENT IS REALLY SHOWING SOME PROMISE. MAN THAT THING IS HUGE. 500Lb WEIGHT SWINGING BACK AND FORTH, ALL FOR THE SAKE OF FREE ENERGY. YOU GOTTA LOVE IT. THANKS FOR WATCHING. MUDDy

THIS VIDEO FINISHES UP UN THE AXIAL FLUX DRAWINGS FOR THIS PROJECTS’ ALTERNATOR STATOR AND MAGNET ROTORS. I ALSO SHOW THE EASY WAY TO DRAW IT. AND SOME MORE INTERESTING THEORY. I’M GLAD TO BE THIS FAR. NOW WE CAN START BUILDING THIS FUN JEWEL. MUDDy

IN THIS VIDEO,I SHOW THE NEWLY MADE BRACE FOR THE YAW BEARING INSTALLED, AND WELDED, THEN WE CUT SOME PIECES FOR MAKING THE TAIL PIVOT, ( MORE METAL WORK AND WELDING, I SHOW HOW TO SET THE TAIL PIVOT UP, I SHOW THE TAIL PIVOT INSTALLED AND WELDED. THINGS ARE COMING TOGETHER. SORRY ABOUT SOME OF THE CAMERA WORK WHEN BOOMER IS CUTTING. IT SEEMS THAT IT TAKES A LITTLE MORE ATTENTION TO HOLD THE CAMERA AND PUT OUT FIRES AT THE SAME TIME. I GUESS I SHOULD HAVE USED THE TRIPOD. LOL. I HAD A BALL AT BOOMERS. I HAD ORIGINALLY PLANNED ON 2 OR 3 DAYS THERE, BUT IT TUNRED INTO A FULL WEEK, BECAUSE MELISSA HAD TO WORK EXTRA HOURS AT WORK, AND COULD NOT COME GET ME.. THAT TURNED OUT TO BE A BLESSING. IT ALLOWED US TO GET A BIT MORE DONE AND FINISH UP THE GREEN MACHINE FOR BOOMERS PURPOSES. KEEP SMILING AND HAVE A BALL. GOD BLESS YOU AND YOURS. MUDDy

THIS VIDEO IS AN INTRODUCTION TO THE 10 FOOT DUAL PERMANENT MAGNET ROTOR AXIAL FLUX WIND TURBINE GENERATOR CONSTRUCTION. JUST AN OVER VIEW AND SOME SAFETY TIPS ON MAGNET USE. IN THIS SERIES I WILL TRY TO EXPLAIN EVERY DETAIL THAT I CAN TO ENSURE THAT THERE ARE NO MISCONCEPTIONS AT ALL ABOUT HOW TO, AND HOW IT WORKS. PLUS WE WILL DESIGN THIS UNIT ON VIDEO TO GET A GRASP OF WHAT IS INVOLVED IN MAKING A GOOD DESIGN. HOW TO DESIGN COILS AND THEIR SHAPE, PLUS THE WINDER DIMENSIONS, COIL DIMENSIONS, MAGNET SAFTEY, THE VALUE OF TESTING BEFORE COMMITING TO ANY DETAIL OF THE DESIGN. HOPE YOU ENJOY! MUDDy